Cat V(5) Neo Core Platinum
Why buy from Hurricane?
This is probably the most frequent questions anyone in business is asked.
At the end of the day people really only wanna know if we can save them on the light bill so I decided to make a video to help you draw your own conclusion.
The vast majority of the country is in a low wind zone lighter shades of blue or white.... if this is your area you should consider this PMA. If you are blessed with higher wind speed average consider our Mark II or III with heavier windings.
We are willing to go the extra mile. We will meet or exceed anyone's warranty in the business. We have the parts in stock and if something goes wrong with you product we are not faced with the decision to take the "hit" and throw the product in the dumpster. Logically speaking, if we can build it we can repair it.
Dual PMA shown performing under water
The following is written with the intent of addressing wind applications but many of the principles apply to electromagnetic - mechanical transfer of energy in general. I will attempt here to lay out the basics as many of my new to the field. My customers want information and facts not puffery exaggerated, claims and “fantastic assertions”.How a Wind Generator works
The science is what it is and we will tell you exactly why you should buy from Hurricane. The majority of what you have read while shopping for a wind generator PMA is fiction as I have eluded previously. We have inserted the following playlist so you may see the science behind the products if you are new to the field.
>The law of conservation of energy applies “ energy can neither be created nor destroyed but change form eg kinetic to mechanic, mechanical to electrical" ect.
Simply stated it takes power to make power. To achieve maximum power from a wind generator the two elements which are of the essential are the amount of power or torque input from a source or blades set, and the efficiency of the generator.
The circumference of the rotor area, number of blades are some of the variables which determine torque produced from a given rotor/blade set. The input torque eg. Maximum mechanical energy input is relative to the amount of electrical energy that can be extracted from generator. These same principle of torque input apply whether we are speaking of a wind generator, hydro, gas, diesel or any other power source which drive a permanent magnet alternator. In other words it takes power to make power
Myth… the claw or zig zag design in a permanent magnet alternator is inferior?
About Rotors Why the claw shape is superior....
The rotor has 7 poles sets distributed as "claws" around it's circumference. One set of claws is thus a "north" pole and the other set is a "south" poles. The epoxy coated N 45 neo core magnet In Hurricane Rotors deeply saturates the stator. The iron originally used in the pole claw has been replaced utilizing higher efficiency shapes and forged steel a used in Hurricane permanent magnet alternators. The magnetic flux lines within the rotor are largely constrained to flow from one pole to the other through the claw structures at each end trapezoidal claw, folding around the internal magnetic structure and passing between the claws through a zig-zag shaped circumferential air gap. There is no reverse flux flow through the rotor shaft itself. The rotor shaft is magnetically entrained and acts as yet another part of the rotor Magnetic rotor.The shape of the zig-zag gap between the claw pieces, being air and much less permeable than the forged steel and directs the magnetic flux into a similar zig-zag shape. So as the rotor rotates there will be a position where this gap exactly bisects a stator segment and both the "north" and the "south" claws on either side of the gap will have an equal magnetic influence on it. As it continues to rotate more and more of the "north" or "south" claw will come adjacent to this particular stator coil, thus transferring the particular magnetic field polarity into it. This zig-zag "claw" design therefore prevents abrupt magnetic transitions from taking place in the stator segments as the rotor is turned. preventing abrupt transitions this elegant design thus largely eliminates any tendency to have a location, or a series of locations, where the magnetic path is more permeable and thus more attractive than adjacent locations. It is these variations in permeability around the circumference that are the cause of magnetic "cogging" in slotted magnet rotor designs.
Of three companies rotor we examine which use this design two of three used magnet to wide for the field which is highly inefficient causing huge losses, heat buildup, e.g. eddy current resistive effects. In other words opposing poles entering the same field essentially fight against each other We have examined multiple "plate and grove designs" and I as well as many customers have found that some of the companies offering this type of design build PMA which have a terrible cogging effect and provide virtually no low end power .
Faraday- Lenz Law
Systems do not like change!
The things that you should be concerned with when buying a generator for maximum efficiency are as follows.
1.Rotor design and strength……this is simple as strong as possible designed in a manner in which the shaft is not difficult to turn and is designed in a manner to promote cogging. Also there are poor designs on the market I have examine that has poles to wide for the fields thus making the PMA terribly inefficient.
2. The air gap between the rotor and stator must be exact. This cannot be done be hand and should be done with precision to the 1000th of an inch to maximize efficiency
3. Stators should be wound with a gauge of wire and winding connection that is appropriate for the particular application. E.g. high wind, wind. Battery bank voltage environment e.g. 12, 24, or 48 volt or the set point for the grid tie you are using. We use 400 degree wire in out stators which will withstand the test of time and extreme conditions. There is nothing magical about a hand wound stator other that the manufacturer could not afford to have enough wound to his specifications and made per the requirement he desired. Moreover by having the buying power to have our product wound professionally the wind is tighter allowing more copper to be wound into areas withing the stator which have deep flux saturation.
4.CRAFTSMANSHIP all connections must be made professionally, products such as lock tite used new parts forged with precision, A PMA is only as good as the person building it. If something does not fot precisely it is not good. Quality Control and balance of the rotating assembly not only effect performance they effect the longevity of a product. An out of balance product will wear the air gap between rotor and stator and guarantee a short bearing live.
5 Value. We pledge you will not find a better product for the money period.
Hurricane Learning LAB: if you are interested in the science behind the products here it is. No pitch nothing fancy it is what it is.
Finally I do not consider myself the ultimate authority on Physics if you have a PHD in your pocket and have feedback we would love to hear from you.
If your permanent magnet alternator manufacturer does not understand the principles contained within this playlist, they will be inept whether their task be manufacturing or importing. Perhaps it's time to consider a Hurricane.
Building a DIY turbine and thinking of using water pipe? Not so fast we have got the parts for you. Safe time and do DIY the safe way
.our blades have great surface area and a lot of great features great for low wind startup and eliminates the need for furling. This listing is for three blade this is for three 36 Great for turbine with output generators 600-800 watts. Using smaller blades will result in less output as the diameter of the blade determines kinetic energy or torque input to the generator or permanent magnet alternator
Could be used as replacement for Hy Energy, Aleko Skymax and of course as used on Vector and XP Turbines. If buying as a replacement blade contact seller prior to purchase to check for blade weight and or compatibility
Hurricane wind power is making our wind turbine blades available that we use on our XP and Vector wind Turbines. We have had good luck with these blade which feature one major advantage over our competitors!
It called Dynamic blade braking:
Hurricane Stealth Storm Wind Turbine Blades utilize their airfoil as a method of breaking eliminating the need for furling and the associated wear that comes with the turbne being violently moved about in high winds which contribute both to bearing wear, blade tension and many other undesirable forces acting on small wind turbines in high speed wind operation.
Hurricane Stealth Storm Wind Turbine Blades utilize asymmetrical and twisted aerodynamic design which ensures rotor capture maximum power from wind (Cp>0.32 in low wind) and operates in amazingly low noise and minimal vibration.
Large ratio of tip section chord to root section chord and variable chord airfoil blade ensures rotor start-up easily and running smoothly with high torque & RPM at low wind conditions Aerodynamic blades designed with over-speed dynamic blade braking systems ensure the generator is well protected in higher winds.
Reinforced nylon glass-fiber using advanced thermoplastic engineering and precision injection molding technology for higher strength, flexibility and reliability .Cp.>0.32 at low wind
Typical wind turbines have three moving parts The generator head, yawing and mechanical furling body parts, Hurricane replaced mechanical furling by using advanced electromagnetic and Dynamic blade braking which only take two moving parts, this in turn improves generator reliability significantly as it is subject to less mechanical failure and bearing wear from stress and impact.
Smart Stealth Blade Aerodynamics Braking and Electromagnetic Speed Limitation
Abandoned the traditional failure-prone mechanical furling system, the blade itself is designed with over-speed braking system which will generate a reverse reluctant torque to lower the blade rotation speed so that the blades and generator can be well protected in higher wind, it solved safety and reliability problems facing by
most small wind turbines. Combination of Electromagnetic braking and aerodynamic braking maximizes energy capture by extending turbine’s operating speed range into higher and lower wind speed which are missed by the old style wind turbines
The blades have exceptional consistency and aerodynamic outline with a mass distribution which ensures the rotor/ blade set operates with minimal vibration and very low noise. Perfectly matched to the Hurricane White Lightening XP and Vector wind generators the blade cause much less resonance of the wind turbine and tower.
Blade Aerodynamics Braking limits blade to rotate at the rated RPM which could avoid higher noise and vibration caused by extreme wind. Wind turbine with minimal vibration and low noise can be mounted on rooftop safely and its operation won’t affect the resident.